Search results
2226
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
2227
[Page extract]
ASTM D3826
ASTM D3826 is a tensile test method, which covers a degradation-end point, or a brittle point) for degradable polyethylene/polypropylene films and sheeting less than 1.0 mm thick.
2228
[Page extract]
BS EN 12814-7
BS EN 12814-7 is a tensile test method with waisted test specimens for testing welded joints of thermoplastics semi-finished products.
2229
[Page extract]
ASTM D642-00
This test method covers compression tests on shipping containers (for example, boxes and drums) or components, or both. Shipping containers may be tested with or without contents.
2230
[Page extract]
BS EN ISO 8339
This International Standard specifies a method for the determination of the tensile properties of sealants used in joints in building construction.
2231
Event
Understanding Adhesion Strength: 180 Degree Peel Test
Across many households and industries, consumers have developed a strong preference for and confidence in ‘Duct Tape’ for all types of uses and applications. This is mainly due to the adhesion strength.
2232
[Page extract]
EN TS 15945
The purpose of DD CEN/TS 15945 is to specify test methods to evaluate the ease of opening of consumer packages, in order to improve easy access to the contents. For packages regulated for safety or similar reasons, e.g.
2233
[Page extract]
BS ISO 2285
BS ISO 2285 is a test method for determining the tension set under constant elongation of vulcanised rubber or thermoplastic.
2234
[Page extract]
ASTM D905-08
This test method covers the determination of the comparative shear strengths of adhesive bonds used for bonding wood and other similar materials, when tested on a standard specimen under specified conditions of preparation, conditioning, and loading in
2235
[Page extract]
ANSI/EIA 364
Mating and Unmating Procedure for Force Testing of Electrical Connectors and Sockets
2236
[Page extract]
FINAT FTM2
This test method differs from FTM 1 in that it can allow the end user to compare the repositionability of different laminates.
2237
[Page extract]
Standards for yield point testing
Yield point testing protocols are defined by recognised international standards, including:
2238
[Page extract]
ASTM D6534-05
This test method covers the determination of the peak force-to-actuate, sometimes called force-to-actuate (FTA), of a mechanical pump dispenser.
2239
Case study
Kim để ferrule kiểm tra kéo ra
Yêu cầu Khách hàng, Oxford Instruments, muốn thực hiện một thử nghiệm kéo phá hủy để đánh giá lực căng tối đa để kéo 2 thành phần ra xa nhau.
2240
[Page extract]
BS EN 12562
Synthetic fibres, Polyamide fibres, Aramide fibres, Textile products, Textile testing, Yarn, Filament yarns, Filaments, Filament (textile fibre), Yarn testing, Yarn linear density determination, Elongation at fracture, Elongation, Force measurement, Mec
2241
[Page extract]
BS EN ISO 10618
Carbon fibres, Mechanical properties of materials, Tensile strength, Tensile testing, Plastics, Impregnated materials, Yarn, Modulus of elasticity, Strain, Tensile strain, Loading, Reinforcing materials, Composite materials, Test equipment, Test specime
2242
[Page extract]
ASTM C273/C273M
This test method is used to determine core shear properties of a sandwich construction material using loading plates bonded to the outer surfaces or skins (facesheets).
2243
[Page extract]
BS EN ISO 527-1
BS EN ISO 527-1 specifies the general principles for determining the tensile properties of plastics and plastic composites under defined conditions.
2244
[Page extract]
ASTM D7078/D7078M-12
This test method covers the determination of the shear properties of high-modulus fiber-reinforced composite materials by clamping the ends of a V-notched specimen between two pairs of loading rails.
2245
[Page extract]
ASTM D6862-11
This test method is useful for acceptance and quality control testing. Adherends, application procedure, and sample conditioning shall be as agreed upon by the manufacturer and the user of the adherends and the adhesive.
2246
[Page extract]
ASTM D937-97
1.1 This test method covers measuring with a penetrometer the penetration of petrolatum as an empirical measure of consistency.
2247
[Page extract]
ISO 11502
Describes a qualitative and a quantitative method for assessing the tendency of flexible plastics films and sheets to adhere to one another when left in contact for some time, at a specified temperature and under light pressure.
2248
[Page extract]
BS ISO 7322
This International Standard specifies test methods for the determination of the following characteristics of composition cork (= product obtained from the agglutination of cork granules with the addition of a binder generally not derived from cork cells
2249
[Page extract]
SAE J 1523
This SAE Recommended Practice defines a procedure for determining shear strengths of adhesives used for bonding automotive oil metal substrates.
2250
[Page extract]
TAPPI T 804
This method is used for measuring the ability of corrugated or solid fiber shipping containers to resist external compressive forces.