Battery terminal weld integrity tensile test

Case study
“The MultiTest 2.5-i is very reliable and we have had no problems since we purchased it. Because it’s failure-free, accurate and has intuitive operation (very user-friendly software) it’s superior to the older control system from another supplier. It’s also worth to mention the after-sales support from ITA, Mecmesin’s Polish Distributor, is quick and efficient.”

Miroslaw Bratus, Production Purchase Coordinator
BMZ Poland Sp.z.o.o.

Battery terminal pull-off tensile testing in production facility

Crimped cable connector pull-off force

Case study
Purchase of the MultiTest 50-xt has allowed us to extend the range of products we can test in-house and obtain more information about the failure mode of the samples.

Erica Moore, Test and EHS Manager
Amphenol

Secure gripping of the crimped contact surface ensures accurate strength of the joint is calculated

Cable and pipe pull-out force batch testing system

Case study
"We have made pull-out tests for many years, but with our new equipment, we get the result much quicker and with better accuracy. We can rapidly prepare and perform advanced tests and present the result in a more precise way for both customers and our colleagues, within research and development. The new equipment enables studies of how much force is needed to make a cable or pipe start moving within a seal. The test fixture was developed at CA Mätsystem AB (Mecmesin’s distributor) in Sweden, especially for Roxtec products, in order to enable a thorough testing of all existing Roxtec solutions. All results are stored in a database providing extended knowledge for future product development, as well as, useful information for customers and sales people."

Patrik Cederholm, Tests & Certificates Engineer
Roxtec International AB

Flexible pipe pull-out test frame for specimen location

Electrical harness terminal testing

Case study
We have been very satisfied with our purchase of the Mecmesin MultiTest 1-x, it has become an essential part of our quality control, system and allows us to calibrate our tooling and ensure our product is as reliable as possible in the severe environment of motorsport.

Nigel Barber, Senior Engineer
Cyprium Motorsports

BS 5G 178-1
Electrical harness crimp testing on site
Our Mecmesin Multitest-dV tester has improved efficiency, accuracy and consistency of our in-house testing. Also the customer service / support has been very helpful throughout. We would definitely recommend Mecmesin.

Ashley Adlam, Quality Supervisor, Quality Control
Tecni Ltd.

Case study
Wire rope crimp test close-up on gauge

Battery terminal weld integrity tensile test

“The MultiTest 2.5-i is very reliable and we have had no problems since we purchased it. Because it’s failure-free, accurate and has intuitive operation (very user-friendly software) it’s superior to the older control system from another supplier. It’s also worth to mention the after-sales support from ITA, Mecmesin’s Polish Distributor, is quick and efficient.”

Miroslaw Bratus, Production Purchase Coordinator
BMZ Poland Sp.z.o.o.

Case study
Battery terminal pull-off tensile testing in production facility
We manufacture some high specification cable assemblies where reliability is a must. In some cases, lives literally depend on the cables not having failures in situations. By using Mecmesin equipment, we can ensure that our product more than meets the UL standard by at least one and a half times the stated requirement, which is the basis of all tests performed by Telecom Connections Limited, thus increasing reliability, increasing quality and most importantly assuring the end-user that the product will meet the demands intended.

Sean Lathey, Quality/IT Manager
Telecom Connections Ltd

Case study
Cable crimp pull testing systems on-site

Crimped cable connector pull-off force

Purchase of the MultiTest 50-xt has allowed us to extend the range of products we can test in-house and obtain more information about the failure mode of the samples.

Erica Moore, Test and EHS Manager
Amphenol

Case study
Secure gripping of the crimped contact surface ensures accurate strength of the joint is calculated

Cable and pipe pull-out force batch testing system

"We have made pull-out tests for many years, but with our new equipment, we get the result much quicker and with better accuracy. We can rapidly prepare and perform advanced tests and present the result in a more precise way for both customers and our colleagues, within research and development. The new equipment enables studies of how much force is needed to make a cable or pipe start moving within a seal. The test fixture was developed at CA Mätsystem AB (Mecmesin’s distributor) in Sweden, especially for Roxtec products, in order to enable a thorough testing of all existing Roxtec solutions. All results are stored in a database providing extended knowledge for future product development, as well as, useful information for customers and sales people."

Patrik Cederholm, Tests & Certificates Engineer
Roxtec International AB

Case study
Flexible pipe pull-out test frame for specimen location

Electrical harness terminal testing

We have been very satisfied with our purchase of the Mecmesin MultiTest 1-x, it has become an essential part of our quality control, system and allows us to calibrate our tooling and ensure our product is as reliable as possible in the severe environment of motorsport.

Nigel Barber, Senior Engineer
Cyprium Motorsports

Case study
Electrical harness crimp testing on site
Online demonstrations and training available from Mecmesin technical sales engineers


Online test equipment and training demos

 

As more people are working from home to reduce non-essential travel, our technical sales engineers can provide online equipment demos or training sessions via web-based video calls.

If possible, send in your own samples and our sales team will be able to present your own products being tested.

Get in touch to discuss your requirements and to arrange an online demo or training session.