Search results
2301
[Page extract]
BS EN ISO 7886-1
This document specifies requirements and test methods for verifying the design of empty sterile single use hypodermic syringes, with or without needle, made of plastic or other materials and intended for the aspiration and injection of fluids after fill
2302
[Page extract]
ASTM C297
This test method determines the flatwise tensile strength of the core, the core-to-facing bond, or the facing of an assembled sandwich panel.
2303
[Page extract]
ASTM C961
This test method covers a laboratory procedure for determining the lap shear strength of sealants. It also provides information on the adhesive bond of the sealants to the tested substrates.
2304
Case study
Syringe Luer lock attachment removal
Customised engineering example
Our client is a biomedical company who manufacture HA medical solutions supplied in glass syringes with compression-fit polycarbonate luer locks.
2305
Case study
Şırınga Luer kilit ekinin çıkarılması
Özel mühendislik örneği Müşterimiz, sıkıştırılmış polikarbonat luer kilitli cam şırıngalarda tedarik edilen HA tıbbi çözümler üreten bir biyomedikal şirketidir.
2306
[Page extract]
BS 1726-1
Provides guidance on methods of specifying and tolerancing hot coiled compression springs, and cold coiled springs that fall outside the size range limits specified in BS EN 15800.
2307
[Page extract]
ASTM C674
These test methods cover determination of the modulus of rupture and the modulus of elasticity of fired ceramic whitewares bodies, formed by any fabrication method, and are applicable to both glazed and unglazed test specimens.
2308
[Page extract]
ASTM F607-03
The ASTM F607 test method provides a means of determining the degree to which gasket materials under compressive load adhere to metal surfaces. The test conditions described are indicative of those frequently encountered in gasket applications.
2309
[Page extract]
ISO 20126
This International Standard specifies requirements and test methods for the physical properties of manual toothbrushes in order to promote the safety of these products for their intended use.It does not apply to manual interdental brushes and powered or
2310
[Page extract]
FINAT FTM2
This test method differs from FTM 1 in that it can allow the end user to compare the repositionability of different laminates.
2311
[Page extract]
ASTM D3658
This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.
2312
[Page extract]
BS EN 50289-3-9
Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Flexural strength, Bending stress, Bend testing, Stiffness
2313
[Page extract]
ASTM D3106
This test method covers the determination of the permanent deformation of bare, continuous elastomeric monofilaments and filament yarns made from rubber, spandex, anidex, or other elastomers subjected to prolonged periods of tension.
2314
[Page extract]
ASTM D5-06e1
This test method covers determination of the penetration of semi-solid and solid bituminous materials. The needles, containers and other conditions described in this test method provide for the determinations of penetrations up to 500.
2315
[Page extract]
ISO 527-5
ISO 527-5 specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.
2316
[Page extract]
Standards for texture compression testing
ISO 16305 - Butter firmness
Specifies a method for determining butter firmness under controlled conditions.
2317
[Page extract]
Applications of edge crush testing in packaging
Design and development
ECT results guide engineers in selecting the correct board grade for the intended application, balancing performance and cost.
2318
[Page extract]
ISO 1924-3
Specifies a method for measuring the tensile strength, strain at break, tensile energy absorption and tensile stiffness, using a testing machine operating with a constant rate of elongation (100 mm/min).
2319
[Page extract]
BS 2782-3: 360C
BS 2782-3: Method 360C specifies a test method for testing the tear resistance of plastics film and sheeting by the initiation method
2320
[Page extract]
ASTM D2633
ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.
2321
[Page extract]
ISO 10123
Specifies a method for the determination of the shear strength of anaerobic-curing liquid adhesives used for retaining cylindrical assemblies, pin-and-collar type, or for locking and sealing threaded fasteners.
2322
[Page extract]
BS EN 12814-2
BS EN 12814-2 is a tensile test method for testing welded joints of thermoplastics semi-finished products.
2323
[Page extract]
ISO 17454
ISO 17454 specifies a method for testing the adhesion between layers of multilayer pipes using a pulling test rig.
2324
[Page extract]
TAPPI T 400
This method describes procedures for obtaining a representative sample for testing.