Search results
1251
[Page extract]
BS 4863
Gives safety requirements for playpens for use by children up to 15kg in weight. It covers both rigid sided and mesh sided playpens.
1252
[Page extract]
ISO 2409
Describes a test method for assessing the resistance of paint coatings to separation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to the substrate.
1253
[Page extract]
BS ISO 6133
BS ISO 6133 specifies five methods of calculating, after testing, the tear strength and the adhesion strength of vulcanized rubber or fabrics coated with or adhered to rubber or plastics.
1254
[Page extract]
BS EN ISO 9626
This International Standard specifies the dimensions, surface and mechanical properties of normal- and thin-walled tubing of designated metric sizes 3,4 mm to 0,3 mm, and of extra-thin-walled tubing of designated metric sizes 2,1 mm to 0,6 mm.
1255
[Page extract]
BS EN 1707
Syringes, Conical fittings (syringes), Injection instruments, Locking and locating devices, Fitting, Pipe fittings, Medical equipment, Medical instruments, Blood transfusion equipment, Dimensions, Dimensional tolerances, Performance testing, Leak tests,
1256
[Page extract]
*corp Mastercard CQM: ID-1
Mastercard CQM requirement covers Peel Strength Test (TM-412 #8120#) and Advanced Peel Strength Test (TN-424 #8240#). Methods are based around ISO 10373-1 to determine the peel strength between 2 layers of an ID or security card.
1257
[Page extract]
ASTM D412-16
ASTM D412 is a test standard for testing the tensile stress-strain properties of thermoset rubbers and thermoplastic elastomers. The standard is divided into two test methods.
1258
[Page extract]
ASTM D6742 / D6742M
ASTM D6742 is the standard test method for tensile and compression testing of filled-hole polymer matrix composite laminates. It provides instructions for modifying open-hole tension and compression test methods to determine filled-hole tensile and com
1261
[Page extract]
Baumann tear test
- slit cut laterally in the centre of sample; used to test the tear strength of leather
1262
[Page extract]
Young's modulus
Measure how stiff or elastic a material is under tension or compression with Young’s modulus testing. Universal testing systems provide reliable modulus of elasticity measurements for compliance with global standards like ISO 527 and ASTM D638.
1263
[Page extract]
Needle penetration and drag testing assess the force required to insert a needle into a material and the friction experienced during this process. This test ensures that syringes perform reliably, reducing risks to patients and healthcare providers.
1264
[Page extract]
Ultimate Tensile Strength
What it is, how to measure it, and why it matters
Ultimate tensile strength (UTS) is a critical property used to determine how materials behave under tension. It defines the maximum stress a material can withstand before breaking.
1265
[Page extract]
Abrasion
Abrasion is the surface wear caused by rubbing with another material. The consumer would expect textiles and other products to withstand a certain amount of deterioration.
1266
[Page extract]
Government
The general government sector covers institutions and public bodies where regulations and standards must be strictly adhered to.
1267
Accessory
3-Point Bend Jig, 1 kN, Aluminium, T-slot base
432-248
A lightweight 3-point Bend Jig with 60 mm high upper and lower anvils of 1.5mm radius. Has a support span up to 120 mm.
Ideal for most low-force bending and snapping applications.
For use with T-slot base plate (432-294) - sold separately - to fit…
1268
Accessory
3/8" Lower Chuck Assembly for use on Helixa motor spindle
432-614
A standard self-centering 3-jaw chuck with key.
It has a maximum ⅜" (9.5mm) opening and is connected to the Helixa motor-drive spindle via an adaptor with quick-release grub-screw.
Used to secure a variety of test specimens for torque applications.
1269
Accessory
Extended Dovetail Bracket (for AFG or BFG)
432-326
The extended dovetail bracket provides 70 mm of extra daylight when mounting AFG or BFG force gauges to test stands. Fixing screws included.
Note: maximum load 500N
1270
Accessory
FPT-H1 loadcell calibration checking kit
432-635
For checking the calibration accuracy of loadcell type HILC used on the FPT-H1 Friction-Peel-Tear Tester.
Comprises a fixing plate with pulley, bench clamp and cord.
For use with Lightweight hanger and masses (part numbers 432-655 and 432-656).
1271
Accessory
Adapter, 10 kN, M10 to M12, M to M
432-335
Male-to-male Adapter
Allows a grip to be connected to a force gauge/loadcell or test stand where thread connections are different.
1272
Accessory
Peel Grip for FPT-H1, 50 mm rubber-faced jaws, QC-8 fitting
432-654
This Peel Grip can be used in conjunction with the FPT-H1 90 degree peel fixture kit (part no. 432-620) or the FPT-H1 180 degree peel fixture kit (part no. 432-636). It is preferred over the standard hook fixture when the drawn part of the sample is non-…
1273
Accessory
Dual Footswitches (non-locking type) for pneumatic grips
Mec205-1
Pneumatic grips are the ideal choice when performing tensile tests on sensitive materials that have a tendency to slip or break at point of clamping.
Mec205-1:
Non-locking dual footswitches open the jaws of the pneumatic grip by pressing the foot pedal…
1274
Accessory
Self-levelling Compression Plate Steel - 196 mm, 25 kN, QC-20 fitting
MecS223k-196
MecS223k - 196mm diameter:
Self-levelling allows exact parallelism to be set between the upper and lower plates.. ideal for those applications where it is critical to accurately measure the deformation of a sample.
The MecS223 range of hardened steel…
1275
Accessory
Scissor Grip, 20 kN, QC-20 or QC-32 fitting
Mec11-20
MEC11-20 (Body only) :
Scissor-action grip rated to 20 kN fitted with either QC-20 or QC-32 connection.
Locking function allows the grip to remain open when inserting a specimen.
Spring tension provides enough clamping force to prevent the specimen…