Search results
1701
[Page extract]
How is 180 degree peel testing performed
The test is carried out on a universal testing machine fitted with a suitable peel fixture.
1702
[Page extract]
Conclusion and Best Practices
Adhering to ISO 11040-4 Annex F is essential for manufacturers of pre-filled syringes. Using the right equipment and following best practices ensures that your products meet safety and quality standards.
1703
[Page extract]
Differences and similarities to other corrugated tests
While TAPPI T 824 focuses on the intrinsic crush strength of pre-fluted medium, other common corrugated tests measure different performance factors:
1704
[Page extract]
Benefits of adhering to testing standards
Following recognised standards delivers measurable benefits:
1705
[Page extract]
Interpreting results and ensuring accuracy
Accurate results rely on correct setup and consistent procedures:
1706
[Page extract]
Ultimate Tensile Strength
What it is, how to measure it, and why it matters
Ultimate tensile strength (UTS) is a critical property used to determine how materials behave under tension. It defines the maximum stress a material can withstand before breaking.
1707
[Page extract]
Elongation and Recovery
Elongation and recovery testing is a fundamental process in material science used to measure how far a material can stretch under a given load and how effectively it returns to its original shape once the force is removed.
1708
Product
인체 공학적 노력 테스터
AFG 수동 취급 키트
850-920
Advanced Manual Handling Kit 는 모든 유형의 수동 취급 력 또는 토크의 인체 공학적 영향을 평가하기 위해 밀기, 당기기 및 비틀기 노력을 측정합니다. 전체 키트에는 그립 핑 크래들과 AFG 게이지를 처리중인 물체에 연결하여 하중을 정확하게 측정하기위한 필수 액세서리가 포함되어 있습니다. 또한 선택적 센서의 데이터를 인식하여보다 구체적인 생리 활동을 측정 할 수 있습니다.
1709
[Page extract]
ASTM C297
This test method determines the flatwise tensile strength of the core, the core-to-facing bond, or the facing of an assembled sandwich panel.
1710
Test Frame
MultiTest test frame (single column)
MultiTest test frame
A ballscrew-driven motorised test frame designed to apply tension and compression from 2 N right up to a capacity of 5 kN (1100 lbf).Its versatile construction makes it perfectly suited for testing all kinds of components in a quality…
1711
[Page extract]
ISO 9895
Specifies a method for determining the compressive strength in the machine and cross-directions of paper and board using a short-span compressive tester. It is intended for papers and boards used for the manufacture of containers and boxes.
1712
[Page extract]
ASTM F628-12e3
This specification covers coextruded acrylonitrile-butadiene-styrene (ABS) plastic drain, waste, and vent pipes made to Schedule 40 iron pipe sizes (IPS) with concentric inner and outer solid ABS layers and a closed-cell cellular ABS core.
1713
[Page extract]
SAE AMSSTD
This standard covers the general requirements and methods for testing sandwich core materials and for testing sandwich construction of the types used primarily in aircraft structures.
1714
[Page extract]
ISO 527-4
ISO 527-4 determines the tensile properties of isotropic and orthotropic fibre reinforced plastic composite sheeting and film including the tensile strength and modulus of elasticity, strain, elongation and the tensile energy to break (TEB).
1715
[Page extract]
BS ISO 5893
ISO 5893 specifies requirements for tensile-testing systems operating at constant rate of traverse and suitable for testing rubbers, plastics and adhesives, although any one system may only be applicable to a narrower range of materials.
1716
[Page extract]
ASTM D3574
ASTM D3574 is a test method used for testing soft polyurethane foam used in car seats, mattresses, pillows and other foam products. Samples come in a variety of forms including slab, bonded, and molded flexible cellular urethane foams.
1717
Event
Tensile Testing: Basics, Tips, & Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
1718
Event
Packaging: Establishing repeatability and consistency
Ensuring the quality and durability of packaging is crucial for maintaining product integrity from production to delivery.
1719
Accessory
QC Type F Loadcell Mounting Plate, 25 mm slot c/w M12 bolt for 2.5 kN, 5 kN and 10 kN S-beam loadcells
432-287
QC Type F Loadcell Mounting Plate c/w M12 bolt.
Fitted with 25 mm slot to suit 2500N - 10kN S-beam loadcells. The M12 bolt is used to secure the mounting plate onto the loadcell so that a QC type C Male Post (432-284) can be affixed to the loadcell.
1720
[Page extract]
ISO 11070
Specifies requirements for introducer needles, introducer catheters, sheath introducers, guidewires and dilators supplied in sterile condition and intended for single use in conjunction with intravascular catheters specified in ISO 10555-1.
1723
[Page extract]
ISO 36
ISO 36 determines the strength required to separate two plies of fabric bonded together with rubber, or a rubber and a fabric ply bonded together. This test is referred to as a “T-peel” test, because as the two adherends are pulled apart, they form the
1724
[Page extract]
ASTM F2824-10
1.1 This test method describes a method for the measurement of mechanical seal strength while separating the entire lid (cover/membrane) from a rigid or semi-rigid round container. 1.2 This test method differs from Test Method F88.