Mecmesin | Search results

2351

^{[Page extract]}

ASTM E2658-15

These practices cover procedures and requirements for the calibration and verification of testing machine speed by means of standards calibration devices

2352

^{[Page extract]}

ASTM D937-97

1.1 This test method covers measuring with a penetrometer the penetration of petrolatum as an empirical measure of consistency.

2353

^{[Page extract]}

ASTM D3471

This test method covers the determination of the top-load required to engage lugs on Type IA child-resistant closures.

2354

^{[Page extract]}

ASTM F543-13

This specification provides requirements for materials, finish and marking, care and handling, and the acceptable dimensions and tolerances for metallic bone screws that are implanted into bone.

2355

^{[Page extract]}

ASTM D2344 is a test method, which determines the short-beam strength of high-modulus fiber-reinforced composite materials. It is applicable to all types of parallel fiber reinforced plastics and composites.

2356

^{[Page extract]}

*corp QPF-MC-1209 B

*Strictly confidential* L'Oreal to methods for shear and penetration testing of lipsticks, deodorants etc.

2357

^{[Page extract]}

ASTM D3826

ASTM D3826 is a tensile test method, which covers a degradation-end point, or a brittle point) for degradable polyethylene/polypropylene films and sheeting less than 1.0 mm thick.

2358

^{[Page extract]}

BS EN 1394

BS EN 1394 is a tensile test method to determine the initial circumferential tensile strength of plastic pipes.

2359

^{[Page extract]}

ASTM D5179-16

ASTM D5179 is a test method for determining organic coatings adhesion to a plastic substrate. It can be used to evaluate the adhesion (pull-off strength) of various coating/substrate combinations e.g. paint and varnish.

2360

^{[Page extract]}

ISO 6789

Wrenches, Torque, Hand tools, Screwdrivers, Marking, Approval testing, Quality control, Calibration

2361

^{[Page extract]}

ISO 10354

Simulates in a qualitative manner the forces and effects on an adhesive-bonded joint at a metal-adhesive/primer interface. It can also be used as a method of checking the surface preparation of substrates.

2362

^{[Page extract]}

BS EN 14350-1

Resusable teats and drinking accessories Resusable feeding bottles and drinking cups Single use feeding bottles, feeding teats, feeding bags and drinking accessories, which do not contain fluid when purchased.

2363

^{[Page extract]}

TAPPI T 456

TAPPI T456 is a test method that describes the procedure for the determination of the tensile strength of paper and paperboard after saturation with water.

2364

^{[Page extract]}

FINAT FTM 9

This test method describes a means of assessing probably the most important and yet the hardest to measure property of pressure sensitive materials, the tack.

2365

^{[Page extract]}

ASTM D953-18

ASTM D953 is a test method that covers the determination of the pin-bearing strength of rigid plastics in either sheet form, molded form, or in reinforced thermoset form.

2366

^{[Page extract]}

BS EN ISO 80369-7

This part of ISO 80369 specifies dimensions and requirements for the design and functional performance of small-bore connectors intended to be used for connections in intravascular applications or hypodermic connections in hypodermic applications of med

2367

^{[Page extract]}

ASTM D7084-04

1.1 This test method covers the determination of bulk crush strength of a bed of formed catalyst particles 1⁄32 to 3⁄16 in.

2368

^{[Page extract]}

ASTM C907

This test method covers a laboratory procedure for determining the tensile adhesive strength of a preformed tape sealant. The type of failure can be determined, and the degree of cohesive/adhesive failure can be estimated.

2369

^{[Page extract]}

CETIE Guide 3

This guide is for producers of quality sparkling wines who carry out the secondary fermentation process in the bottle, also known as bottle fermentation.

2370

^{[Page extract]}

BS EN ISO 6789

Wrenches, Torque, Hand tools, Screwdrivers, Marking, Approval testing, Quality control, Calibration

2371

^{[Page extract]}

ASTM C364

This test method covers the compressive properties of structural sandwich construction in a direction parallel to the sandwich facing plane.

2372

^{[Page extract]}

ASTM D4475-02

ASTM D4475 is a test method used for determining the horizontal shear strength of fiber reinforced plastic rods.

2373

^{[Page extract]}

TAPPI T 284

This test evaluates the ability of corrugating medium to contribute to the compression strenght of a corrugated box.

2374

^{[Page extract]}

ASTM D413-98

ASTM D413 is a test method used to determine the force per unit width required to separate a rubber layer from a flexible substrate such as fabric, wire or sheet metal.

2375

^{[Page extract]}

NF S86-604

This document defines the test methods for characterizing metallic watch straps and the corresponding requirements.

Search results

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

システム

試験機

システム

試験機

システム

計測機器

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}