Search results
976
[Page extract]
ASTM D5766 / D5766-M
ASTM D5766 is a test method to determine the open-hole tensile strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibres.
977
Event
Fundamentals of Torque Testing
If you have ever struggled to open your favorite bottle of water or jam or required help loosening the lug nuts on your car’s wheels, it is likely due to a case of over-torque.
978
[Page extract]
Differences and similarities to other corrugated tests
While TAPPI T 824 focuses on the intrinsic crush strength of pre-fluted medium, other common corrugated tests measure different performance factors:
979
Event
Fundamentals of Torque Testing
If you have ever struggled to open your favorite bottle of water or jam or required help loosening the lug nuts on your car’s wheels, it is likely due to a case of over-torque.
980
[Page extract]
ASTM D3470
This test method covers the determination of the force required to cause a downward-force-while-turning lug-finish closure to be rotated across the container finish lugs (strippage) without downward force being applied to the closure (Type IIA closures)
981
[Page extract]
What is the 90-degree peel test?
The 90-degree peel test is a mechanical method used to measure the adhesive strength between two bonded materials.
982
Event
Wire Crimp & Weld Testing Webinar
The only way of really knowing the strength of a crimped terminal is to pull it.
983
[Page extract]
TAPPI T 825
The flat crush test (1) is a measure of the resistance of the flutes in corrugated board to a crushing force applied perpendicular to the surface of the board under prescribed conditions.
984
[Page extract]
ASTM D2659
ASTM D2659 determines the mechanical properties of blown thermoplastic containers under columnar crush conditions at a steady rate of compression. Any container, whether blown commercially or in the laboratory, may be used as the test specimen.
985
[Page extract]
*corp 01M-01-218
To determine the resistance of seams to slip or break down when placed under a continuous load.
986
[Page extract]
Compression
Compression testing is a way of determining how something will react when a compressive force is applied to it. It typically involves measuring the relationship between the applied force and how much the object deforms.
It is performed to:
987
[Page extract]
Bulk analysis
In industries where powders, granules or pelletised materials are formulated, processed or packaged, maintaining consistency in texture and perf
988
Sensor
Sensors - Universal Testers (ELS)
Sensors
The OmniTest universal testers use Mecmesin's range of high-resolution precision Enhanced Load Sensors (ELS) to record tensile and compressive loads.
ELSA precision loadcell connects directly to an OmniTest or MultiTest-dV stand and communicates…
989
[Page extract]
Jewellery & Watch
In jewellery and watch production, alloys, components and other materials must meet the needs of the manufacturing process and the end-product should give good service performance when worn by the customer.
990
Accessory
Force Gauge Gripping Cradle, 2.5 kN
432-388
Allows force gauges to be used as a rigid hand-held instrument (mounting screws supplied).
The dual-handle cradle allows the comfortable application by hand of push/pull loads.
For use with a BFG or AFG digital force gauge.
Commonly used for manual-…
991
Accessory
Lightweight hanger and 5 N slotted mass for verifying FPT 10 N
432-655
A lightweight hanger and an M1 slotted mass of 5N.
For use with the FPT-H1 loadcell calibration checking kit (432-635) to verify the accuracy of HILC 10 N loadcells.
992
Accessory
Rubber coated jaws for Mec154 Heavy-duty Vice Grip, 20kN, 40 x 60 mm
Mec154-BG
Rubber-faced Jaws (40mm high x 60mm wide) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = 0 - 32 mm.
For specimens which may get weakened by pinching at the contact-edge of the grip. (e.g. films, filaments, fibres and…
993
Accessory
Footswitch regulator option
Mec205-PR
Pressure regulator to adjust the air pressure between 1-10 bar.
Useful when a different pressure is required between upper and lower pneumatic grips.
To be ordered and fitted with either Mec205-1 or Mec205-2 Footswitches.
994
Accessory
Charger for touchscreen digital gauges, UK, USB-C, 3-pin square
304-059
For use with Mecmesin touchscreen digital force and torque gauges. With 3 square pins. Commonly used in the UK.
The mains adaptor/charger is a USB-C type:
Input:100-240Vac 50/60Hz 0.6A Max
Output: 5V/3A, 9V/3A,12V/2.25A, 3V-9V/3A 9V-11V/2.45A.
995
Accessory
Miniature Vice Grip, 100 N, QC-20 fitting
MecS341
Versatile, easy to use, and suitable for small components (eg bonded joints) where access is limited and tensile forces are below 100 N.
Clamping surfaces are machined with pyramid-shaped serrations to ensure optimum gripping force.
The flexible chain-…
996
Accessory
Custom-made Safety Guards and Enclosures
PDVguard
Where the standard safety guard does not fulfil your application requirements, Mecmesin can work with you to design and produce a custom-made safety guard to meet your exact requirements. Suitable for any Mecmesin test stand. Previously-designed guards…
997
Accessory
Blank (smooth) jaws for Mec83 U-Form Pneumatic Vice Grip, 5 kN, 40 x 60 mm
Mec83-B
Blank Jaws (40mm x 60mm) - smooth steel jaw. Allows the user to machine or affix own surface (eg. abrasive 'emery' paper).
Opening span = 0-10mm, 10-20mm or 20-30mm depending on which rod and piston are fitted to the Mec83 body.
Supplied as 0.5 set = 2…
998
Accessory
Compression Plate Rectangular, Hardened Steel, 396 x 596 mm, QC-20 or QC-32 fitting
Mec36-396x596-St
MEC36-396x596-St:
Rectangular compression plate in hardened steel featuring concentric circles for helping operators to place samples centrally. Also supplied with 4 fixing legs to support the weight of the steel plate. Suitable for hard specimens such…
999
Accessory
Compression Plate Square, Hardened Steel, 196 x 196 mm, QC-20 or QC-32 fitting
Mec36-196-St
MEC36-196-St :-
Square compression plate in hardened steel featuring concentric circles for helping operators to place samples centrally. Also supplied with 4 fixing legs to support the weight of the steel plate. Suitable for hard specimens such as…
1000
Accessory
FPT-H1 loadcell calibration checking kit
432-635
For checking the calibration accuracy of loadcell type HILC used on the FPT-H1 Friction-Peel-Tear Tester.
Comprises a fixing plate with pulley, bench clamp and cord.
For use with Lightweight hanger and masses (part numbers 432-655 and 432-656).