Search results
376
Case study
Abrasion and micro-scratch testing of wood and laminate surfaces
Requirement
The use of natural materials has long been a unique selling point across many consumer product lines.
377
[Page extract]
Example: Cork extraction testing for bottling efficiency
Designed for high-volume bottling plants, the automated tester measures the extraction force and weight of 75 corks from each production batch.
378
[Page extract]
Significance of connector extraction resistance
Extraction resistance is the connector’s ability to maintain a secure fit during use while still allowing disconnection when necessary. This is especially important where connectors are repeatedly mated and unmated, such as:
379
[Page extract]
Introduction to strain at maximum stress testing
Strain at maximum stress testing is a critical method in material evaluation, providing a precise measurement of how much a material deforms at the point of its highest applied load.
380
[Page extract]
Why is the trapezoidal tear test important?
Tear resistance is a critical measure of a material’s durability, particularly in applications where the material may be subject to punctures, cuts, or repeated stress.
381
Case study
Luer and small-bore connector torque testing
Requirement
International standards relevant to small-bore connectors for liquids and gasses in healthcare applications focus on their ease of use and resistance to leakage or mishandling.
382
Product
Mechanical force gauge
A simple solution for basic push and pull tests applied by hand.
Robust mechanical force gauges designed for general tension and compression tests up to 440 N.
Easy-to-use with an analogue dial and needle pointer, to indicate the force applied.
383
Event
Materials Testing: Theory and Practice Pt. 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
384
Event
Materials Testing: Theory and Practice Pt. 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
385
Case study
Syringe Testing According to ISO 11040-4 Annex F: Needle Penetration and Drag Testing
Explore this comprehensive guide on syringe testing according to ISO 11040-4 Annex F. Learn the step-by-step process of needle penetration and drag testing, the equipment needed, and best practices for accurate results.
386
[Page extract]
Belt/strap grips
Belt and strap grips - typically of a split-roller type in order to provide a rounded, smooth-surface around which a belt or strap can be looped several times.
387
[Page extract]
ASTM D4649-03
This guide covers recommended guidelines and test methods for the selection, specification, and use of stretch wrap films for unitizing, reinforcing, and palletizing for indoor environments.
389
Event
Materials Testing: Theory and Practice Pt. 1 & 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
390
[Page extract]
BS EN ISO 3386
BS EN ISO 3386-1 specifies a method for the determination of the compression stress/strain characteristic of low-density flexible cellular materials up to 250 kg/m3.
391
[Page extract]
ASTM C633
This test method covers the determination of the degree of adhesion (bonding strength) of a coating to a substrate or the cohesion strength of the coating in a tension normal to the surface.
392
[Page extract]
ASTM E328-02
These test methods cover the determination of the time dependence of stress (stress relaxation) in materials and structures under conditions of approximately constant constraint, constant environment, and negligible vibration.
393
[Page extract]
ISO 2409
Describes a test method for assessing the resistance of paint coatings to separation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to the substrate.
394
[Page extract]
ASTM D3410 / D3410M
ASTM D3410 determines the compressive properties of polymer matrix composite materials reinforced by high-modulus fibers.
395
Event
Materials Testing: Theory and Practice Pt. 1
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
396
Product
Advanced force and torque indicator
AFTI
851-401
A versatile force and torque display unit, with interchangeable 'smart' sensors, that provides high accuracy and flexibility.
The AFTI can be used as a handheld device for mobile applications or it can be used as the measurement device for integration…
397
Product
Advanced force and torque indicator
AFTI
851-401
A versatile force and torque display unit, with interchangeable 'smart' sensors, that provides high accuracy and flexibility.
The AFTI can be used as a handheld device for mobile applications or it can be used as the measurement device for integration…
398
Case study
壁に取り付けられた芳香剤の破壊的な負荷の評価
要件顧客は、壁に取り付けられた芳香剤に350Nの制御された負荷をかけ、その上に立っている子供の効果を再現したいと考えていました。荷重は、製品の4つの異なる平面（上部、下部、中間、端など）に順番に適用する必要がありました。顧客は、製品および関連する摩耗特性の包括的な評価を可能にするために、非破壊検査を実行することを望んでいました。試験中にサンプルが破壊された場合、このプロセスが妨げられると感じられました。
399
[Page extract]
ASTM F2923
This specification establishes requirements and test methods for specified elements and certain mechanical hazards in children's jewelry.
400
Product
Cap torque tester
Orbis
876-107
The Orbis digital torque tester is ideally suited for basic clockwise and counter-clockwise torque tests.Manually operated and measuring up to 6 N.m its capacity is ideal for most caps and closures which are intended to be opened by hand.
Providing data…