Search results
1576
Event
Texture Testing for Bakery Applications
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1577
[Page extract]
ASTM D6175-03
5.1 This test method is intended to provide information on the ability of an extruded catalyst to retain physical integrity during use.
1578
Event
Pull Force and Break Strength Testing
Whether it is medical tubing, plastic straws, copper wire or zip ties, pull force and break strength testing is critical not only to production quality but also to consumer safety.
1579
[Page extract]
ASTM D6195-03
These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface.
1580
[Page extract]
ISO 13954
ISO 13954 describes a peel test method for determining the decohesive resistance of polyethylene electrofusion socket assemblies for use in the distribution of fluids.
1581
[Page extract]
ISO 1924-3
Specifies a method for measuring the tensile strength, strain at break, tensile energy absorption and tensile stiffness, using a testing machine operating with a constant rate of elongation (100 mm/min).
1582
[Page extract]
ISO 8067
ISO 8067 specifies two methods for the determination of the tear strength of flexible cellular polymeric materials:
Method A, using a trouser test piece
Method B, using an angle test piece without a nick
1583
[Page extract]
ISO 13445
Specifies a method for the determination of the shear strength of adhesives used to bond materials with elastic moduli higher than the elastic modulus of the adhesive.
1584
[Page extract]
ASTM D882-18
ASTM D882 is a test method that covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness). It is used to measure tensile properties including ultimate tensile
1585
[Page extract]
FINAT FTM 9
This test method describes a means of assessing probably the most important and yet the hardest to measure property of pressure sensitive materials, the tack.
1586
[Page extract]
TAPPI T 810
This method describes a procedure for measuring the bursting strength of single wall and double wall corrugated board within the range of 690 kPa (100psi) to 4825 kPa (700 psi) employing an instrument which uses a disk shaped, molded diaphragm.
1587
[Page extract]
BS EN 12453
BS EN 12453:2001 specifies the performance requirements with regard to the safety in use for any type of power operated doors, gates and barriers intended for installation in areas in the reach of persons, and for which the main intended uses are giving
1588
[Page extract]
ASTM D3787
This test method describes the measurement for bursting strength with a ball burst strength tester of textiles or garments that exhibit a high degree of ultimate elongation.
1589
[Page extract]
ISO 9187-2
ISO 9187-2:2010 specifies materials, dimensions and requirements for forms of one-point-cut (OPC) ampoules (forms B, C and D) for injectables.
Ampoules complying with ISO 9187-2:2010 are intended for single use only.
1590
[Page extract]
ASTM D2148
ASTM D2148 is a test standard that for testing bondable silicone rubber tapes, which form a sealed structure either with the application of heat (and pressure if needed) or by the process of auto-adhesion (self-fusing).
1591
Event
Mechanical Performance Testing of Medical Devices Webinar
A hands-on Force and Torque how-to demonstration event.
1592
[Page extract]
Scissor grips
Scissor grips - self-tightening and self-aligning with the specimen initially being held by spring tension.
1593
[Page extract]
CETIE Guide 1
This guideline applies to the capping of still wines with a cork mouth finish as per CETIE data sheet GME 50.01 which has been used as a base for the European standard EN 12726. Contains reference to 'extraction force', 'cork dimensional recovery', 'ch
1594
[Page extract]
ISO 9047
This International Standard specifies a method for the determination of the adhesion/cohesion properties of sealants with predominantly elastic behaviour which are used in joints in building construction.
1595
[Page extract]
Plates
Compression fixtures should be selected to suit the contact area of the sample which is to be tested.
1596
Event
Compression Force Testing in Automotive Applications
The global automotive industry has never been more competitive. Challenges on materials, fuel efficiency, EV technology and recycling are adding to ever-increasing market demand.
1597
[Page extract]
ASTM D747-10
ASTM D747 is used to determine the flexibility of plastics by means of a cantilever beam.
1598
Event
Fundamentals of Adhesion (Peel) Testing
There is a reason people reach for Duct Tape as a fix for almost everything – Adhesion Strength. From busted pipes to ripped furniture, the preference for a solution that “does not easily peel off” is the guiding principle for manufactures.
1599
[Page extract]
BS EN 5057
Specifies requirements for dimensions, performance characteristics and test programme. section 16 is insertion & withdrawal force test
1600
[Page extract]
ISO 7622-2
ISO 7622-2 specifies a method for the determination of the tensile strength, in the longitudinal, of steel cords constituting the carcass of conveyor belts.
It applies exclusively to conveyor belts with a steel carcass.