Search results
1076
[Page extract]
Secant modulus compared to other moduli
Different moduli are used to describe the stiffness of materials, each calculated at different points on the stress-strain curve:
1077
[Page extract]
Introduction to flexural testing
Flexural testing is a core method in materials science, used to evaluate how materials perform when subjected to bending stresses.
1078
[Page extract]
Introduction to material mechanics
Material mechanics is the study of how materials respond to forces such as tension, compression, torsion and shear. It is a core discipline within engineering, underpinning design, manufacturing and quality assurance across many sectors.
1079
[Page extract]
Speak to an expert
Mecmesin offers fully configurable tensile testing systems that comply with leading ASTM and ISO strip method standards.
1080
[Page extract]
Why Mecmesin for compressibility and recovery testing
Precision systems for all materials
Mecmesin systems test everything from soft foams and elastomers to rigid gasket composites.
1081
[Page extract]
Common challenges and best practices
Accurate four-point bend testing requires attention to several factors:
1082
[Page extract]
Testing applications
Gymnastic equipment safety
Gymnastic rings, beams, and mats are tested to ensure they absorb impacts without losing integrity or rebound performance.
1083
[Page extract]
Mecmesin solutions for compressive hardness testing
Mecmesin designs and supplies precision testing systems for compressive hardness applications across industries.
1084
[Page extract]
Applications of compressive shear testing
Compressive shear testing is applied across multiple industries where materials must withstand shear stresses while compressed.
1085
[Page extract]
Introduction to yield point testing
Yield point testing is essential for understanding the mechanical behaviour of materials.
1086
[Page extract]
Maintenance and calibration of tear testers
To maintain accuracy and extend service life, regular maintenance and calibration are essential.
1087
[Page extract]
Common challenges in yield point testing
Specimen alignment issues
Misalignment during clamping can cause uneven stress distribution, resulting in inaccurate readings.
1088
[Page extract]
Speak to an expert
Selecting the right trapezoidal tear testing setup requires understanding both the material and the relevant standards.
1089
[Page extract]
Featured case studies
Rubber sealing components - ISO 37 testing of an optimised compound achieved a 12 percent increase in strai
1090
[Page extract]
Introduction to secant modulus
In material testing and engineering, understanding how a material responds to applied stress is essential for predicting performance, ensuring safety, and optimising design.
1091
[Page extract]
Performing a five-point bend test
Specimen preparation
Cut specimens to the standardised dimensions specified in ASTM D2718.
Ensure surfaces are smooth and free from defects that could affect results.<
1092
[Page extract]
Key mechanical testing methods
Short span compression testing differs from conventional compression tests because it uses a minimal support length to eliminate bending effects.
1093
[Page extract]
Why choose Mecmesin for tangent modulus testing
Mecmesin designs precision testing systems for reliable, repeatable tangent modulus measurements.
1094
[Page extract]
Testing procedures for electrical connectors
For electrical connectors, insertion and withdrawal testing is essential to ensure reliable contact, mechanical robustness, and compliance with relevant standards.<
1095
[Page extract]
Applications in industry
Lap shear testing under compressive load is widely used across multiple sectors:
1096
[Page extract]
Why Mecmesin for pull-off and pull-out testing
Mecmesin designs and manufactures tensile and adhesion testing equipment for both destructive and non-destructive pull-off and pull-out applications.
1097
[Page extract]
Applications in demanding sectors
The strip method is used wherever fabric integrity under load is critical:
1098
[Page extract]
Why Mecmesin for climbing drum peel testing
Precision peel testing systems
Mecmesin offers test platforms such as the OmniTest and
1099
[Page extract]
How is 180 degree peel testing performed
The test is carried out on a universal testing machine fitted with a suitable peel fixture.
1100
[Page extract]
Applications in advanced ceramics and composites
Four-point bend testing is the preferred approach for assessing the flexural strength of advanced ceramics<