Search results
2901
[Page extract]
ASTM E2658-15
These practices cover procedures and requirements for the calibration and verification of testing machine speed by means of standards calibration devices
2902
[Page extract]
ISO 2409
Describes a test method for assessing the resistance of paint coatings to separation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to the substrate.
2903
[Page extract]
IEC 62137-1-1
The test method described in IEC 62137-1-1:2007 is applicable to gull-wing lead surface mounting components.
2904
[Page extract]
ISO 7263
Specifies two methods for the determination of the flat crush resistance of a corrugating medium after laboratory fluting.
2905
[Page extract]
*corp QPF-MC-1209 B
*Strictly confidential*
L'Oreal to methods for shear and penetration testing of lipsticks, deodorants etc.
2906
[Page extract]
TAPPI T 576
This test method decribes the procedure, using constant-rate-of-elongation, for determining three tensile breaking properties of towel and tissue: tensile strength, stretch, and tensi;e energy absorption.
2907
[Page extract]
NF B 57 100
Section 8 covers the measurement of the tensileforce to extract a natural or synthetic cork from a still wine bottle or from a standardised glass tube, which simulates the profile of the neck of a wine bottle.
2908
[Page extract]
BS EN 12467
Sheet materials, Asbestos cement, Cements, Fibres, Reinforced materials, Sheet roof coverings, Cladding (buildings), Curtain walling, Grades (quality), Density, Strength of materials, Approval testing, Type testing, Quality control, Acceptance inspectio
2909
[Page extract]
TAPPI T 841
This method describes procedures for determining the edgewise compressive strength, parallel to the flutes, of a short column of single wall and double wall corrugated fiberboard.
2910
[Page extract]
ASTM C364
This test method covers the compressive properties of structural sandwich construction in a direction parallel to the sandwich facing plane.
2911
[Page extract]
ASTM D952-15
ASTM D952 is a test method that covers the determination of the bond strength or ply adhesion strength of sheet plastic and electrical insulating materials.
2912
[Page extract]
CETIE Guide 12
This guide describes the five essential rules to be observed to properly crimp a pump with an aluminium ferrule on an FEA type glass finish used for perfumery, according to the EN 14854 standard and the Cetie document GME 40.05.
2913
[Page extract]
ASTM D3330
These test methods cover the measurement of the peel adhesion of single and double-sided pressure-sensitive tapes.
2914
[Page extract]
ASTM D5169-98
This test method measures the shear strength of hook and loop touch fasteners using a recording constant rate of extension (CRE) tensile testing machine.
2915
[Page extract]
ASTM D816-06
These test methods cover tests to measure the properties of adhesives, commonly called rubber cements, that may be applied in plastic or fluid form and that are manufactured from natural rubber, reclaimed rubber, synthetic elastomers, or combinations of
2916
[Page extract]
SAE AS7928
This specification covers insulated and uninsulated crimp-style copper terminal lugs and conductor splices for stranded conductors. An Amendment corresponding to this standard is available at AS7928_A1
2917
[Page extract]
ASTM D7030-04
This test method covers determining the resistance of an empty paper corrugated shipping container to a vertically applied constant compression load for a specified time.
2918
[Page extract]
ISO 3377-2
ISO 3377-2:2016 specifies a method for determining the tear strength of leather using a double-edged tear. The method is sometimes described as the Baumann tear. It is applicable to all types of leather.
2919
[Page extract]
BS EN 12445
This standard specifies the test methods to be applied to a power operated door to demonstrate compliance with the requirements specidied in EN 12453: 2000 in particular it specifies the method of measuring the forces developed by a power operated door.
2920
[Page extract]
ASTM F806-99a
ASTM F806 is a test method that covers determination of the short-time compressibility and recovery at room temperature of laminated composite gasket materials.
2921
[Page extract]
SAE AS1310B
This SAE Aerospace Standard (AS) is intended for use by those involved in the design of aircraft, missile, or space systems, and their support equipment to define the various type of fastener torque.
2922
[Page extract]
ASTM D3474
This standard covers the calibration and use of torque meters of the type normally used in packaging applications.
2923
Event
Tensile Testing: Basics, Tips and Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
2924
Event
Materials Testing: Theory and Practice Pt. 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
2925
[Page extract]
IEC 60512-13-1
Details a standard test method to measure the force to fully engage or separate mating connectors, including the effect of any locking, latching, sealing, engaging, separating or similar device, that assists or resists such operation.