Search results
1576
[Page extract]
ASTM D882-18
ASTM D882 is a test method that covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness). It is used to measure tensile properties including ultimate tensile
1577
[Page extract]
FINAT FTM 9
This test method describes a means of assessing probably the most important and yet the hardest to measure property of pressure sensitive materials, the tack.
1578
[Page extract]
TAPPI T 810
This method describes a procedure for measuring the bursting strength of single wall and double wall corrugated board within the range of 690 kPa (100psi) to 4825 kPa (700 psi) employing an instrument which uses a disk shaped, molded diaphragm.
1579
[Page extract]
BS EN 12453
BS EN 12453:2001 specifies the performance requirements with regard to the safety in use for any type of power operated doors, gates and barriers intended for installation in areas in the reach of persons, and for which the main intended uses are giving
1580
[Page extract]
ASTM D3787
This test method describes the measurement for bursting strength with a ball burst strength tester of textiles or garments that exhibit a high degree of ultimate elongation.
1581
[Page extract]
ISO 9187-2
ISO 9187-2:2010 specifies materials, dimensions and requirements for forms of one-point-cut (OPC) ampoules (forms B, C and D) for injectables.
Ampoules complying with ISO 9187-2:2010 are intended for single use only.
1582
[Page extract]
ASTM D2148
ASTM D2148 is a test standard that for testing bondable silicone rubber tapes, which form a sealed structure either with the application of heat (and pressure if needed) or by the process of auto-adhesion (self-fusing).
1583
Event
Mechanical Performance Testing of Medical Devices Webinar
A hands-on Force and Torque how-to demonstration event.
1584
[Page extract]
Scissor grips
Scissor grips - self-tightening and self-aligning with the specimen initially being held by spring tension.
1585
[Page extract]
CETIE Guide 1
This guideline applies to the capping of still wines with a cork mouth finish as per CETIE data sheet GME 50.01 which has been used as a base for the European standard EN 12726. Contains reference to 'extraction force', 'cork dimensional recovery', 'ch
1586
[Page extract]
ISO 9047
This International Standard specifies a method for the determination of the adhesion/cohesion properties of sealants with predominantly elastic behaviour which are used in joints in building construction.
1587
[Page extract]
Plates
Compression fixtures should be selected to suit the contact area of the sample which is to be tested.
1588
Event
Compression Force Testing in Automotive Applications
The global automotive industry has never been more competitive. Challenges on materials, fuel efficiency, EV technology and recycling are adding to ever-increasing market demand.
1589
[Page extract]
ASTM D747-10
ASTM D747 is used to determine the flexibility of plastics by means of a cantilever beam.
1590
Event
Fundamentals of Adhesion (Peel) Testing
There is a reason people reach for Duct Tape as a fix for almost everything – Adhesion Strength. From busted pipes to ripped furniture, the preference for a solution that “does not easily peel off” is the guiding principle for manufactures.
1591
[Page extract]
BS EN 5057
Specifies requirements for dimensions, performance characteristics and test programme. section 16 is insertion & withdrawal force test
1592
[Page extract]
ISO 7622-2
ISO 7622-2 specifies a method for the determination of the tensile strength, in the longitudinal, of steel cords constituting the carcass of conveyor belts.
It applies exclusively to conveyor belts with a steel carcass.
1593
Event
Materials Testing: Theory and Practice Pt. 1 & 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
1595
[Page extract]
ASTM D2534
The coefficient of friction is related to the slip properties of many commercial articles that have been coated with petroleum wax (for example, butter cartons and wax-impregnated or hot melt coated corrugated board).
1596
Event
Coefficient of Friction (COF) Testing
Coefficient of Friction (COF) testing measures the static and kinetic friction values to help determine the quality of the final product.
1597
[Page extract]
ASTM D3470
This test method covers the determination of the force required to cause a downward-force-while-turning lug-finish closure to be rotated across the container finish lugs (strippage) without downward force being applied to the closure (Type IIA closures)
1598
Marco de prueba
Vortex-dv test frame
Vortex test frame
A sturdy twin-column test frame capable of applying torque up to 10 N.m (90 lbf.in). Tall and wide enough to accept a variety of test specimens yet compact to use as a bench-top tester.
View test frame
1599
[Page extract]
ASTM D6241-04
This test method for determining the puncture strength of geotextiles is to be used by the industry as an index of puncture strength.
1600
[Page extract]
ASTM D3578
Scope... 1.1 This specification describes certain requirements for natural rubber gloves used in conducting medical examinations and diagnostic and therapeutic procedures. It also covers natural rubber gloves used in handling contaminated medical