Search results
1526
[Page extract]
Understanding the stress-strain curve
The stress-strain curve is a primary tool for tensile strength analysis. It shows how a material responds to an increasing tensile load, providing detailed insights into its mechanical properties.
1527
[Page extract]
Introduction to compressive strength testing
Compressive strength testing is essential for evaluating the ability of materials to withstand axial loads, which are forces that push or pull them.
1528
[Page extract]
IEC 61210
IEC 61210:2010 applies to non-insulated flat quick-connect terminations consisting of a male tab of size 2,8 mm, 4,8 mm, 6,3 mm or 9,5 mm with hole or dimple detents and a mating female connector for use as either an incorporated or an integrated part o
1529
[Page extract]
ASTM F2132-01
This specification provides the performance requirements and associated test procedures for the puncture resistance of materials used in the construction of containers for discarded medical needles and other sharps.
1530
Case study
Fast-Food-Tray-Crush-Test
Anforderung Als Lieferant von Fast-Food-Schalen musste der Kunde sicherstellen, dass die Schalen einer bestimmten Seitenkraft standhalten, ohne Schaden zu nehmen, damit sie beim Umgang mit und beim Laden von Lebensmitteln nicht brechen.
1531
Event
Essentials of grip & fixture selection in force & torque testing
For a test to work, the test system needs to properly interface with its specimen.
1532
[Page extract]
Best practices in conducting cone penetration tests
Step-by-step procedure
Sample preparation - Condition the sample according to the standard, controlling temperature and humidity where required.
Equipment calibration - Confirm the
1533
[Page extract]
EN 22872
EN 22872 specifies two methods for testing complete, filled transport packages for compression resistance.
1534
[Page extract]
Introduction to penetration and puncture resistance testing
Penetration and puncture resistance testing are essential for evaluating how well a material can withstand force from sharp, pointed, or blunt objects.
1535
[Page extract]
Introduction to chord modulus
Chord modulus is a key parameter in material testing, providing engineers and quality control teams with a precise measure of a material’s stiffness under defined loading conditions.
1536
[Page extract]
ASTM D2063/D2063M
This test method measures torque retention properties of container/continuous thread closure systems with the use of a non-automated, spring torque-meter (with either a dial indicator or a digital readout) or a torque wrench. evaluation.
1537
[Page extract]
ISO 8033
ISO 8033 specifies methods for the determination of the adhesion between lining and reinforcement, between cover and reinforcement, between reinforcement layers, between cover and outer lamination (thin layer of material outside the cover for protection
1538
[Page extract]
Common test methods and standards
Internationally recognised standards ensure that compressibility and recovery testing is consistent and repeatable across laboratories and production sites.
1539
Case study
Festliche Festigkeitsüberprüfung des Mauerwerks der Beleuchtung
Anforderung Eine Reihe von Kommunen im Vereinigten Königreich haben einen neuen Verhaltenskodex für die Installation, den Betrieb und die Entfernung von saisonalen Dekorationen verabschiedet.
1540
Case study
Industrial fixtures and fasteners
Requirement
SFS intec is a global supplier of precision components, special fasteners and mechanical fastening elements, with long-standing customer relationships, in the aerospace, automotive and construction industries.
1541
[Page extract]
Applications across industries
Compressive hardness testing is applied in many sectors to confirm that materials meet performance and safety criteria.
1542
[Page extract]
Introduction to yield point testing
Yield point testing is essential for understanding the mechanical behaviour of materials.
1543
[Page extract]
Torque testing methods
Programmable torque testers
Motorised torque testers allow engineers to define torque profiles, control rotational speed, and capture the complete torque-tension curve.
1544
[Page extract]
Destructive and non-destructive methods
Testing may be performed destructively or non-destructively depending on the objectives.
1545
Case study
Bogenbefestigungs-Abzugsprüfung an der Kleidung
Anforderung Der Kunde war Zulieferer des großen britischen Bekleidungshändlers Marks & Spencer, der vorschreibt, dass alle Verschlüsse und Befestigungen auf Fehler getestet werden müssen.
1546
[Page extract]
ISO 9187-1
ISO 9187-1:2010 specifies materials, dimensions, capacities, performance and packaging requirements for three forms of glass ampoule (forms B, C and D) for injectable pharmaceutical products.
1548
[Page extract]
Introduction to single lap shear testing
Single lap shear testing is a widely used method for determining the shear strength of an adhesive bond between two overlapping materials.
1549
[Page extract]
ISO 11070
Specifies requirements for introducer needles, introducer catheters, sheath introducers, guidewires and dilators supplied in sterile condition and intended for single use in conjunction with intravascular catheters specified in ISO 10555-1.
1550
Case study
Schraubenhaltekraft von Baustoffen
Anforderung Ein führender Hersteller und Vertreiber von Metalldachsystemen für das Baugewerbe wollte die Ausreißkraft von Schrauben ermitteln, die an Baumaterialien befestigt sind.