Search results
976
Event
Wire Crimp & Weld Testing Webinar
The only way of really knowing the strength of a crimped terminal is to pull it.
977
[Page extract]
ISBT PTC-00004
These ISBT (International Society of Beverage Technologists) Sport Closure test methods focus on child safety related parameters such as separation forces and choking hazards of closure components.
978
[Page extract]
ASTM D790-17
ASTM D790 is used to determine the flexural properties of unreinforced and reinforced plastics, including high modulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to a simply supported beam (spec
979
Case study
Spider Silk Tensile Strength and Toughness
Requirement
The University of Nottingham is a global education facility – with campuses in the UK, China and Malaysia.
980
Case study
Prüfung der Folienspannung
Anforderung Der Kunde verwendet eine zweilagige Kunststofffolie als Verpackungsfolie für Tiernahrung und Süßwaren.
981
Event
VectorPro Software - The ultimate platform for force & materials testing
VectorPro Software: The ultimate platform for force & materials testing
Presenters: Carl Bramley / Moses Da Rocha
982
[Page extract]
BS EN 12090
Thermal insulating materials, Thermal insulation, Construction materials, Shear testing, Shear strength, Shear stress, Specimen preparation, Formulae (mathematics), Test specimens, Test equipment, Testing conditions, Adhesives, Mechanical testing, Repor
983
[Page extract]
ASTM D4255 / D4255M-15a
ASTM D4255 is a test method for testing the in-plane shear properties of high-modulus fiber-reinforced composite materials. The method is divided into two procedures. Procedure A tests laminates clamped between two pairs of loading rails.
984
[Page extract]
ASTM D3916
ASTM D3916 is a test method for determining the tensile properties of pultruded, glass-fiber-reinforced thermosetting plastic rod of diameters ranging from 3.2 mm to 25.4 mm.
985
[Page extract]
ASTM d6108-19
ASTM D6108 covers the determination of the mechanical properties of plastic lumber and shapes, when the entire cross-section is loaded in compression at relatively low uniform rates of straining or loading.
986
[Page extract]
ASTM C273/C273M
This test method is used to determine core shear properties of a sandwich construction material using loading plates bonded to the outer surfaces or skins (facesheets).
987
Case study
Schältest von halbstarren Verpackungen für Medizinprodukte
Beispiel für kundenspezifisches Engineering Unser Kunde musste die Ablösequalität eines Tyvek®-Papierdeckels testen, der zum Versiegeln einer sterilen, halbsteifen, tiefgezogenen Kunststoffschale mit Fertigspritzen verwendet wurde.
988
Case study
Glued cardboard packaging integrity
Requirement
Graphic Packaging International is a leading designer and manufacturer of food and beverage packaging.
989
Case study
Stabilisierte Federprüfung
Beispiel für kundenspezifisches Engineering Unser Kunde musste eine Reihe kleiner, leichter Federn unter Druck testen.
990
[Page extract]
ASTM D4475-02
ASTM D4475 is a test method used for determining the horizontal shear strength of fiber reinforced plastic rods.
991
[Page extract]
ASTM D3470
This test method covers the determination of the force required to cause a downward-force-while-turning lug-finish closure to be rotated across the container finish lugs (strippage) without downward force being applied to the closure (Type IIA closures)
992
[Page extract]
ASTM D2979
This test method covers measurement of the pressure-sensitive tack of adhesives.
993
Case study
Motorcycle switchgear actuation forces
Requirement
A leading German motorcycle manufacturer wanted to perform a series of tests to evaluate the actuation forces on its handlebar-mounted controls.
994
Case study
Verwendung einer UTM als Kalibrierungswerkzeug für Wägezellen
Anforderung Wenn es darum geht, eine Wägezelle unter Zug und Druck zu konfigurieren und zu kalibrieren, kann dies ein zeitaufwändiger Prozess sein, insbesondere wenn die betreffenden Lasten zu hoch sind, um einen Satz kalibrierter Gewichte (a
995
Event
Cap Closure and Removal Torque Testing
The primary objective for measuring and analyzing the torque characteristics of a container cap is to accurately determine not only the quality of the part or process, but also the root cause of a wide variety of defects.
996
[Page extract]
ASTM D2063/D2063M
This test method measures torque retention properties of container/continuous thread closure systems with the use of a non-automated, spring torque-meter (with either a dial indicator or a digital readout) or a torque wrench. evaluation.
997
Case study
Bottle cap torque testing with custom mandrels
Requirement
A key element, when measuring the opening and closing torque characteristics between a bottle and its cap, is to minimise any distortion of the closure by gripping evenly and uniformly.
998
Case study
Prüfung der Trennkraft der Schrotpatronen und der Crimpfestigkeit
Anforderung
Bei der Herstellung von Kleinwaffenmunition wie Schrotpatronen sind die Schrotkugeln, das Wad und das Pulver in einer Plastikhülle enthalten.
999
Case study
Inline respiratory filter pull test
Customised engineering example
A manufacturer of filtration products needed to test the extraction force of a respiratory filter when pulled from within an inline medical device.
1000
Case study
Zugfestigkeitsprüfung des Rohmaterials für Metall-Läden
Anforderung Soprofen Industrie ist ein führender französischer Hersteller von Metallrollläden und Garagentoren.